This commit fixes an issue where if a nomad client and server shared the same consul instance, the server would deregister any services and checks registered by clients for running tasks.
Guard against Canary being set to false at the same time as an
allocation is being stopped: this could cause RemoveTask to be called
with the wrong Canary value and leaking a service.
Deleting both Canary values is the safest route.
Also refactor Consul ServiceClient to take a struct instead of a massive
set of arguments. Meant updating a lot of code but it should be far
easier to extend in the future as you will only need to update a single
struct instead of every single call site.
Adds an e2e test for canary tags.
Periodically sync services and checks from Nomad to Consul. This is
mostly useful when testing with the Consul dev agent which does not
persist state across restarts. However, this is a reasonable safety
measure to prevent skew between Consul's state and Nomad's
services+checks.
Also modernized the test suite a bit.
Instead of checking Consul's version on startup to see if it supports
TLSSkipVerify, assume that it does and only log in the job service
handler if we discover Consul does not support TLSSkipVerify.
The old code would break TLSSkipVerify support if Nomad started before
Consul (such as on system boot) as TLSSkipVerify would default to false
if Consul wasn't running. Since TLSSkipVerify has been supported since
Consul 0.7.2, it's safe to relax our handling.
Related to #3681
If a user specifies an invalid port *label* when using
address_mode=driver they'll get an error message about the label being
an invalid number which is very confusing.
I also added a bunch of testing around Service.AddressMode validation
since I was concerned by the linked issue that there were cases I was
missing. Unfortunately when address_mode=driver is used there's only so
much validation that can be done as structs/structs.go validation never
peeks into the driver config which would be needed to verify the port
labels/map.
Fixes#3681
When in drive address mode Nomad should always advertise the driver's IP
in Consul even when no network exists. This matches the 0.6 behavior.
When in host address mode Nomad advertises the alloc's network's IP if
one exists. Otherwise it lets Consul determine the IP.
I also added some much needed logging around Docker's network discovery.
The allocID and taskName parameters are useless for agents, but it's
still nice to reuse the same hash method for agent and task services.
This brings in the lowercase mode for the agent hash as well.
Fixes#3620
Previously we concatenated tags into task service IDs. This could break
deregistration of tag names that contained double //s like some Fabio
tags.
This change breaks service ID backward compatibility so on upgrade all
users services and checks will be removed and re-added with new IDs.
This change has the side effect of including all service fields in the
ID's hash, so we no longer have to track PortLabel and AddressMode
changes independently.
Also skip getting an address for script checks which don't use them.
Fixed a weird invalid reserved port in a TaskRunner test helper as well
as a problem with our mock Alloc/Job. Hopefully the latter doesn't cause
other tests to fail, but we were referencing an invalid PortLabel and
just not catching it before.
Fixes#3380
Adds address_mode to checks (but no auto) and allows services and checks
to set literal port numbers when using address_mode=driver.
This allows SDNs, overlays, etc to advertise internal and host addresses
as well as do checks against either.
Before this commit if a task had 2 checks cause restarts at the same
time, both would trigger restarts of the task! This change removes all
checks for a task whenever one of them is restarted.
@dadgar made the excellent observation in #3105 that TaskRunner removes
and re-registers checks on restarts. This means checkWatcher doesn't
need to do *any* internal restart tracking. Individual checks can just
remove themselves and be re-added when the task restarts.
Fixes an issue in which the allocation health watcher was checking for
allocations health based on un-interpolated services and checks. Change
the interface for retrieving check information from Consul to retrieving
all registered services and checks by allocation. In the future this
will allow us to output nicer messages.
Fixes https://github.com/hashicorp/nomad/issues/2969
From https://golang.org/pkg/sync/atomic/#pkg-note-BUG :
On both ARM and x86-32, it is the caller's responsibility to arrange for
64-bit alignment of 64-bit words accessed atomically. The first word in
a global variable or in an allocated struct or slice can be relied upon
to be 64-bit aligned.
Fixes#2891
Previously the agent services and checks were being asynchrously
deregistered on shutdown, so it was a race between the sync goroutine
deregistering them and Nomad shutting down.
This switches to synchronously deregister agent serivces and checks
which doesn't really have a downside since the sync goroutines retry
behavior doesn't help on shutdown anyway.
* alloc_runner
* Random tests
* parallel task_runner and no exec compatible check
* Parallel client
* Fail fast and use random ports
* Fix docker port mapping
* Make concurrent pull less timing dependant
* up parallel
* Fixes
* don't build chroots in parallel on travis
* Reduce parallelism on travis with lxc/rkt
* make java test app not run forever
* drop parallelism a little
* use docker ports that are out of the os's ephemeral port range
* Limit even more on travis
* rkt deadline
Fixes#2827
This is a tradeoff. The pro is that you can run separate client and
server agents on the same node and advertise both. The con is that if a
Nomad agent crashes and isn't restarted on that node in the same mode
its entry will not be cleaned up.
That con scenario seems far less likely to occur than the scenario on
the pro side, and even if we do leak an agent entry the checks will be
failing so nothing should attempt to use it.
This PR adds watching of allocation health at the client. The client can
watch for health based on the tasks running on time and also based on
the consul checks passing.
Ideally DriverNetwork would be fully populated in Driver.Prestart, but
Docker doesn't assign the container's IP until you start the container.
However, it's important to setup the port env vars before calling
Driver.Start, so Prestart should populate that.
Previously was interpolating the original task's services again.
Fixes#2180
Also fixes a slight memory leak in the new consul agent. Script check
handles weren't being deleted after cancellation.
Previous implementation assumed all struct fields were included in
service and check IDs. Service IDs never include port labels and check
IDs *optionally* include port labels, so lots of things had to change.
Added a really big test to exercise this.
Michael Schurter