This PR introduces the `address` field in the `service` block so that Nomad
or Consul services can be registered with a custom `.Address.` to advertise.
The address can be an IP address or domain name. If the `address` field is
set, the `service.address_mode` must be set in `auto` mode.
This PR implements first-class support for Nomad running Consul
Connect Mesh Gateways. Mesh gateways enable services in the Connect
mesh to make cross-DC connections via gateways, where each datacenter
may not have full node interconnectivity.
Consul docs with more information:
https://www.consul.io/docs/connect/gateways/mesh-gateway
The following group level service block can be used to establish
a Connect mesh gateway.
service {
connect {
gateway {
mesh {
// no configuration
}
}
}
}
Services can make use of a mesh gateway by configuring so in their
upstream blocks, e.g.
service {
connect {
sidecar_service {
proxy {
upstreams {
destination_name = "<service>"
local_bind_port = <port>
datacenter = "<datacenter>"
mesh_gateway {
mode = "<mode>"
}
}
}
}
}
}
Typical use of a mesh gateway is to create a bridge between datacenters.
A mesh gateway should then be configured with a service port that is
mapped from a host_network configured on a WAN interface in Nomad agent
config, e.g.
client {
host_network "public" {
interface = "eth1"
}
}
Create a port mapping in the group.network block for use by the mesh
gateway service from the public host_network, e.g.
network {
mode = "bridge"
port "mesh_wan" {
host_network = "public"
}
}
Use this port label for the service.port of the mesh gateway, e.g.
service {
name = "mesh-gateway"
port = "mesh_wan"
connect {
gateway {
mesh {}
}
}
}
Currently Envoy is the only supported gateway implementation in Consul.
By default Nomad client will run the latest official Envoy docker image
supported by the local Consul agent. The Envoy task can be customized
by setting `meta.connect.gateway_image` in agent config or by setting
the `connect.sidecar_task` block.
Gateways require Consul 1.8.0+, enforced by the Nomad scheduler.
Closes#9446
This PR fixes a bug where Nomad was more restrictive on Ingress Gateway Configuration
Entry definitions than Consul. Before, Nomad would not allow for declaring IGCEs with
http listeners with service name "*", which is a special feature allowable by Consul.
Note: to make http protocol work, a service-default must be defined setting the
protocol to http for each service.
Fixes: #9729
Allow for readiness type checks by configuring nomad to ignore warnings
or errors reported by a service check. This allows the deployment to
progress and while Consul handles introducing the sercive into a
resource pool once the check passes.
This PR implements Nomad built-in support for running Consul Connect
terminating gateways. Such a gateway can be used by services running
inside the service mesh to access "legacy" services running outside
the service mesh while still making use of Consul's service identity
based networking and ACL policies.
https://www.consul.io/docs/connect/gateways/terminating-gateway
These gateways are declared as part of a task group level service
definition within the connect stanza.
service {
connect {
gateway {
proxy {
// envoy proxy configuration
}
terminating {
// terminating-gateway configuration entry
}
}
}
}
Currently Envoy is the only supported gateway implementation in
Consul. The gateay task can be customized by configuring the
connect.sidecar_task block.
When the gateway.terminating field is set, Nomad will write/update
the Configuration Entry into Consul on job submission. Because CEs
are global in scope and there may be more than one Nomad cluster
communicating with Consul, there is an assumption that any terminating
gateway defined in Nomad for a particular service will be the same
among Nomad clusters.
Gateways require Consul 1.8.0+, checked by a node constraint.
Closes#9445
* Prevent Job Statuses from being calculated twice
https://github.com/hashicorp/nomad/pull/8435 introduced atomic eval
insertion iwth job (de-)registration. This change removes a now obsolete
guard which checked if the index was equal to the job.CreateIndex, which
would empty the status. Now that the job regisration eval insetion is
atomic with the registration this check is no longer necessary to set
the job statuses correctly.
* test to ensure only single job event for job register
* periodic e2e
* separate job update summary step
* fix updatejobstability to use copy instead of modified reference of job
* update envoygatewaybindaddresses copy to prevent job diff on null vs empty
* set ConsulGatewayBindAddress to empty map instead of nil
fix nil assertions for empty map
rm unnecessary guard
This PR fixes a long standing bug where submitting jobs with changes
to connect services would not trigger updates as expected. Previously,
service blocks were not considered as sources of destructive updates
since they could be synced with consul non-destructively. With Connect,
task group services that have changes to their connect block or to
the service port should be destructive, since the network plumbing of
the alloc is going to need updating.
Fixes#8596#7991
Non-destructive half in #7192
This PR adds initial support for running Consul Connect Ingress Gateways (CIGs) in Nomad. These gateways are declared as part of a task group level service definition within the connect stanza.
```hcl
service {
connect {
gateway {
proxy {
// envoy proxy configuration
}
ingress {
// ingress-gateway configuration entry
}
}
}
}
```
A gateway can be run in `bridge` or `host` networking mode, with the caveat that host networking necessitates manually specifying the Envoy admin listener (which cannot be disabled) via the service port value.
Currently Envoy is the only supported gateway implementation in Consul, and Nomad only supports running Envoy as a gateway using the docker driver.
Aims to address #8294 and tangentially #8647
This change adds the ability to set the fields `success_before_passing` and
`failures_before_critical` on Consul service check definitions. This is a
feature added to Consul v1.7.0 and later.
https://www.consul.io/docs/agent/checks#success-failures-before-passing-critical
Nomad doesn't do much besides pass the fields through to Consul.
Fixes#6913
This PR adds the capability of running Connect Native Tasks on Nomad,
particularly when TLS and ACLs are enabled on Consul.
The `connect` stanza now includes a `native` parameter, which can be
set to the name of task that backs the Connect Native Consul service.
There is a new Client configuration parameter for the `consul` stanza
called `share_ssl`. Like `allow_unauthenticated` the default value is
true, but recommended to be disabled in production environments. When
enabled, the Nomad Client's Consul TLS information is shared with
Connect Native tasks through the normal Consul environment variables.
This does NOT include auth or token information.
If Consul ACLs are enabled, Service Identity Tokens are automatically
and injected into the Connect Native task through the CONSUL_HTTP_TOKEN
environment variable.
Any of the automatically set environment variables can be overridden by
the Connect Native task using the `env` stanza.
Fixes#6083
Before, if the sidecar_service stanza of a connect enabled service
was missing, the job submission would cause a panic in the nomad
agent. Since the panic was happening in the API handler the agent
itself continued running, but this change will the condition more
gracefully.
By fixing the `Copy` method, the API handler now returns the proper
error.
$ nomad job run foo.nomad
Error submitting job: Unexpected response code: 500 (1 error occurred:
* Task group api validation failed: 2 errors occurred:
* Missing tasks for task group
* Task group service validation failed: 1 error occurred:
* Service[0] count-api validation failed: 1 error occurred:
* Consul Connect must be native or use a sidecar service
Enable configuration of HTTP and gRPC endpoints which should be exposed by
the Connect sidecar proxy. This changeset is the first "non-magical" pass
that lays the groundwork for enabling Consul service checks for tasks
running in a network namespace because they are Connect-enabled. The changes
here provide for full configuration of the
connect {
sidecar_service {
proxy {
expose {
paths = [{
path = <exposed endpoint>
protocol = <http or grpc>
local_path_port = <local endpoint port>
listener_port = <inbound mesh port>
}, ... ]
}
}
}
stanza. Everything from `expose` and below is new, and partially implements
the precedent set by Consul:
https://www.consul.io/docs/connect/registration/service-registration.html#expose-paths-configuration-reference
Combined with a task-group level network port-mapping in the form:
port "exposeExample" { to = -1 }
it is now possible to "punch a hole" through the network namespace
to a specific HTTP or gRPC path, with the anticipated use case of creating
Consul checks on Connect enabled services.
A future PR may introduce more automagic behavior, where we can do things like
1) auto-fill the 'expose.path.local_path_port' with the default value of the
'service.port' value for task-group level connect-enabled services.
2) automatically generate a port-mapping
3) enable an 'expose.checks' flag which automatically creates exposed endpoints
for every compatible consul service check (http/grpc checks on connect
enabled services).
Fix a bug where consul service definitions would not be updated if changes
were made to the service in the Nomad job. Currently this only fixes the
bug for cases where the fix is a matter of updating consul agent's service
registration. There is related bug where destructive changes are required
(see #6877) which will be fixed in another PR.
The enable_tag_override configuration setting for the parent service is
applied to the sidecar service.
Fixes#6459
Without a `LocalServicePort`, Connect services will try to use the
mapped port even when delivering traffic locally. A user can override
this behavior by pinning the port value in the `service` stanza but
this prevents us from using the Consul service name to reach the
service.
This commits configures the Consul proxy with its `LocalServicePort`
and `LocalServiceAddress` fields.
* jobspec: breakup parse.go into smaller files
* add sidecar_task parsing to jobspec and api
* jobspec: combine service parsing logic for task and group service stanzas
* api: use slice of ConsulUpstream values instead of pointers
Seth Hoenig