We require any non-wildcard services to match the protocol defined in
the listener on write, so that we can maintain a consistent experience
through ingress gateways. This also helps guard against accidental
misconfiguration by a user.
- Update tests that require an updated protocol for ingress gateways
This now requires some type of protocol setting in ingress gateway tests
to ensure the services are not filtered out.
- small refactor to add a max(x, y) function
- Use internal configEntryTxn function and add MaxUint64 to lib
* Implements a simple, tcp ingress gateway workflow
This adds a new type of gateway for allowing Ingress traffic into Connect from external services.
Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>
This config entry will be used to configure terminating gateways.
It accepts the name of the gateway and a list of services the gateway will represent.
For each service users will be able to specify: its name, namespace, and additional options for TLS origination.
Co-authored-by: Kyle Havlovitz <kylehav@gmail.com>
Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>
* Add Ingress gateway config entry and other relevant structs
* Add api package tests for ingress gateways
* Embed EnterpriseMeta into ingress service struct
* Add namespace fields to api module and test consul config write decoding
* Don't require a port for ingress gateways
* Add snakeJSON and camelJSON cases in command test
* Run Normalize on service's ent metadata
Sadly cannot think of a way to test this in OSS.
* Every protocol requires at least 1 service
* Validate ingress protocols
* Update agent/structs/config_entry_gateways.go
Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>
Co-authored-by: Freddy <freddygv@users.noreply.github.com>
Previously this happened to be validating only the chains in the default namespace. Now it will validate all chains in all namespaces when the global proxy-defaults is changed.
Failover is pushed entirely down to the data plane by creating envoy
clusters and putting each successive destination in a different load
assignment priority band. For example this shows that normally requests
go to 1.2.3.4:8080 but when that fails they go to 6.7.8.9:8080:
- name: foo
load_assignment:
cluster_name: foo
policy:
overprovisioning_factor: 100000
endpoints:
- priority: 0
lb_endpoints:
- endpoint:
address:
socket_address:
address: 1.2.3.4
port_value: 8080
- priority: 1
lb_endpoints:
- endpoint:
address:
socket_address:
address: 6.7.8.9
port_value: 8080
Mesh gateways route requests based solely on the SNI header tacked onto
the TLS layer. Envoy currently only lets you configure the outbound SNI
header at the cluster layer.
If you try to failover through a mesh gateway you ideally would
configure the SNI value per endpoint, but that's not possible in envoy
today.
This PR introduces a simpler way around the problem for now:
1. We identify any target of failover that will use mesh gateway mode local or
remote and then further isolate any resolver node in the compiled discovery
chain that has a failover destination set to one of those targets.
2. For each of these resolvers we will perform a small measurement of
comparative healths of the endpoints that come back from the health API for the
set of primary target and serial failover targets. We walk the list of targets
in order and if any endpoint is healthy we return that target, otherwise we
move on to the next target.
3. The CDS and EDS endpoints both perform the measurements in (2) for the
affected resolver nodes.
4. For CDS this measurement selects which TLS SNI field to use for the cluster
(note the cluster is always going to be named for the primary target)
5. For EDS this measurement selects which set of endpoints will populate the
cluster. Priority tiered failover is ignored.
One of the big downsides to this approach to failover is that the failover
detection and correction is going to be controlled by consul rather than
deferring that entirely to the data plane as with the prior version. This also
means that we are bound to only failover using official health signals and
cannot make use of data plane signals like outlier detection to affect
failover.
In this specific scenario the lack of data plane signals is ok because the
effectiveness is already muted by the fact that the ultimate destination
endpoints will have their data plane signals scrambled when they pass through
the mesh gateway wrapper anyway so we're not losing much.
Another related fix is that we now use the endpoint health from the
underlying service, not the health of the gateway (regardless of
failover mode).
freddygv