* Remove some usage of md5 from the system
OSS side of https://github.com/hashicorp/consul-enterprise/pull/1253
This is a potential security issue because an attacker could conceivably manipulate inputs to cause persistence files to collide, effectively deleting the persistence file for one of the colliding elements.
Signed-off-by: Mark Anderson <manderson@hashicorp.com>
If multiple instances of a service are co-located on the same node then
their proxies will all share a cache entry for their resolved service
configuration. This is because the cache key contains the name of the
watched service but does not take into account the ID of the watching
proxies.
This means that there will be multiple agent service manager watches
that can wake up on the same cache update. These watchers then
concurrently modify the value in the cache when merging the resolved
config into the local proxy definitions.
To avoid this concurrent map write we will only delete the key from
opaque config in the local proxy definition after the merge, rather
than from the cached value before the merge.
This PR replaces the original boolean used to configure transparent
proxy mode. It was replaced with a string mode that can be set to:
- "": Empty string is the default for when the setting should be
defaulted from other configuration like config entries.
- "direct": Direct mode is how applications originally opted into the
mesh. Proxy listeners need to be dialed directly.
- "transparent": Transparent mode enables configuring Envoy as a
transparent proxy. Traffic must be captured and redirected to the
inbound and outbound listeners.
This PR also adds a struct for transparent proxy specific configuration.
Initially this is not stored as a pointer. Will revisit that decision
before GA.
The method is only used in tests, and only exists for legacy calls.
There was one other package which used this method in tests. Export
the AddServiceRequest and a couple of its fields so the new function can
be used in those tests.
Add a skip condition to all tests slower than 100ms.
This change was made using `gotestsum tool slowest` with data from the
last 3 CI runs of master.
See https://github.com/gotestyourself/gotestsum#finding-and-skipping-slow-tests
With this change:
```
$ time go test -count=1 -short ./agent
ok github.com/hashicorp/consul/agent 0.743s
real 0m4.791s
$ time go test -count=1 -short ./agent/consul
ok github.com/hashicorp/consul/agent/consul 4.229s
real 0m8.769s
```
TestAgent.Key was only used by 3 tests. Extracting it from the common helper that is used in hundreds of
tests helps keep the shared part small and more focused.
This required a second change (which I was planning on making anyway), which was to change the behaviour of
DataDir. Now in all cases the TestAgent will use the DataDir, and clean it up once the test is complete.
This function now only starts the agent.
Using:
git grep -l 'StartTestAgent(t, true,' | \
xargs sed -i -e 's/StartTestAgent(t, true,/StartTestAgent(t,/g'
* Cleanup the discovery chain compilation route handling
Nothing functionally should be different here. The real difference is that when creating new targets or handling route destinations we use the router config entries name and namespace instead of that of the top level request. Today they SHOULD always be the same but that may not always be the case. This hopefully also makes it easier to understand how the router entries are handled.
* Refactor a small bit of the service manager tests in oss
We used to use the stringHash function to compute part of the filename where things would get persisted to. This has been changed in the core code to calling the StringHash method on the ServiceID type. It just so happens that the new method will output the same value for anything in the default namespace (by design actually). However, logically this filename computation in the test should do the same thing as the core code itself so I updated it here.
Also of note is that newer enterprise-only tests for the service manager cannot use the old stringHash function at all because it will produce incorrect results for non-default namespaces.
* Use consts for well known tagged adress keys
* Add ipv4 and ipv6 tagged addresses for node lan and wan
* Add ipv4 and ipv6 tagged addresses for service lan and wan
* Use IPv4 and IPv6 address in DNS
Also:
* Finished threading replaceExistingChecks setting (from GH-4905)
through service manager.
* Respected the original configSource value that was used to register a
service or a check when restoring persisted data.
* Run several existing tests with and without central config enabled
(not exhaustive yet).
* Switch to ioutil.ReadFile for all types of agent persistence.
* Add integration test for central config; fix central config WIP
* Add integration test for central config; fix central config WIP
* Set proxy protocol correctly and begin adding upstream support
* Add upstreams to service config cache key and start new notify watcher if they change.
This doesn't update the tests to pass though.
* Fix some merging logic get things working manually with a hack (TODO fix properly)
* Simplification to not allow enabling sidecars centrally - it makes no sense without upstreams anyway
* Test compile again and obvious ones pass. Lots of failures locally not debugged yet but may be flakes. Pushing up to see what CI does
* Fix up service manageer and API test failures
* Remove the enable command since it no longer makes much sense without being able to turn on sidecar proxies centrally
* Remove version.go hack - will make integration test fail until release
* Remove unused code from commands and upstream merge
* Re-bump version to 1.5.0
* Add HTTP endpoints for config entry management
* Finish implementing decoding in the HTTP Config entry apply endpoint
* Add CAS operation to the config entry apply endpoint
Also use this for the bootstrapping and move the config entry decoding function into the structs package.
* First pass at the API client for the config entries
* Fixup some of the ConfigEntry APIs
Return a singular response object instead of a list for the ConfigEntry.Get RPC. This gets plumbed through the HTTP API as well.
Dont return QueryMeta in the JSON response for the config entry listing HTTP API. Instead just return a list of config entries.
* Minor API client fixes
* Attempt at some ConfigEntry api client tests
These don’t currently work due to weak typing in JSON
* Get some of the api client tests passing
* Implement reflectwalk magic to correct JSON encoding a ProxyConfigEntry
Also added a test for the HTTP endpoint that exposes the problem. However, since the test doesn’t actually do the JSON encode/decode its still failing.
* Move MapWalk magic into a binary marshaller instead of JSON.
* Add a MapWalk test
* Get rid of unused func
* Get rid of unused imports
* Fixup some tests now that the decoding from msgpack coerces things into json compat types
* Stub out most of the central config cli
Fully implement the config read command.
* Basic config delete command implementation
* Implement config write command
* Implement config list subcommand
Not entirely sure about the output here. Its basically the read output indented with a line specifying the kind/name of each type which is also duplicated in the indented output.
* Update command usage
* Update some help usage formatting
* Add the connect enable helper cli command
* Update list command output
* Rename the config entry API client methods.
* Use renamed apis
* Implement config write tests
Stub the others with the noTabs tests.
* Change list output format
Now just simply output 1 line per named config
* Add config read tests
* Add invalid args write test.
* Add config delete tests
* Add config list tests
* Add connect enable tests
* Update some CLI commands to use CAS ops
This also modifies the HTTP API for a write op to return a boolean indicating whether the value was written or not.
* Fix up the HTTP API CAS tests as I realized they weren’t testing what they should.
* Update config entry rpc tests to properly test CAS
* Fix up a few more tests
* Fix some tests that using ConfigEntries.Apply
* Update config_write_test.go
* Get rid of unused import
Mark Anderson