Previous to this commit, the API response would include Gateway
Addresses in the form `domain.name.:8080`, which due to the addition of
the port is probably not the expected response.
This commit rightTrims any `.` characters from the end of the domain
before formatting the address to include the port resulting in
`domain.name:8080`
These types are used as values (not pointers) in other structs. Using a pointer receiver causes
problems when the value is printed. fmt will not call the String method if it is passed a value
and the String method has a pointer receiver. By using a value receiver the correct string is printed.
Also remove some unused methods.
Fixes#8466
Since Consul 1.8.0 there was a bug in how ingress gateway protocol
compatibility was enforced. At the point in time that an ingress-gateway
config entry was modified the discovery chain for each upstream was
checked to ensure the ingress gateway protocol matched. Unfortunately
future modifications of other config entries were not validated against
existing ingress-gateway definitions, such as:
1. create tcp ingress-gateway pointing to 'api' (ok)
2. create service-defaults for 'api' setting protocol=http (worked, but not ok)
3. create service-splitter or service-router for 'api' (worked, but caused an agent panic)
If you were to do these in a different order, it would fail without a
crash:
1. create service-defaults for 'api' setting protocol=http (ok)
2. create service-splitter or service-router for 'api' (ok)
3. create tcp ingress-gateway pointing to 'api' (fail with message about
protocol mismatch)
This PR introduces the missing validation. The two new behaviors are:
1. create tcp ingress-gateway pointing to 'api' (ok)
2. (NEW) create service-defaults for 'api' setting protocol=http ("ok" for back compat)
3. (NEW) create service-splitter or service-router for 'api' (fail with
message about protocol mismatch)
In consideration for any existing users that may be inadvertently be
falling into item (2) above, that is now officiall a valid configuration
to be in. For anyone falling into item (3) above while you cannot use
the API to manufacture that scenario anymore, anyone that has old (now
bad) data will still be able to have the agent use them just enough to
generate a new agent/proxycfg error message rather than a panic.
Unfortunately we just don't have enough information to properly fix the
config entries.
Previously, we were only returning a single ListenerPort for a single
service. However, we actually allow a single service to be serviced over
multiple ports, as well as allow users to define what hostnames they
expect their services to be contacted over. When no hosts are defined,
we return the default ingress domain for any configured DNS domain.
To show this in the UI, we modify the gateway-services-nodes API to
return a GatewayConfig.Addresses field, which is a list of addresses
over which the specific service can be contacted.
We can only allow host names that are valid domain names because we put
these hosts into a DNSSAN. In addition, we validate that the wildcard
specifier '*' is only present as the leftmost label to allow for a
wildcard DNSSAN and associated wildcard Host routing in the ingress
gateway proxy.
- Validate that this cannot be set on a 'tcp' listener nor on a wildcard
service.
- Add Hosts field to api and test in consul config write CLI
- xds: Configure envoy with user-provided hosts from ingress gateways
This commit adds the necessary changes to allow an ingress gateway to
route traffic from a single defined port to multiple different upstream
services in the Consul mesh.
To do this, we now require all HTTP requests coming into the ingress
gateway to specify a Host header that matches "<service-name>.*" in
order to correctly route traffic to the correct service.
- Differentiate multiple listener's route names by port
- Adds a case in xds for allowing default discovery chains to create a
route configuration when on an ingress gateway. This allows default
services to easily use host header routing
- ingress-gateways have a single route config for each listener
that utilizes domain matching to route to different services.
* Implements a simple, tcp ingress gateway workflow
This adds a new type of gateway for allowing Ingress traffic into Connect from external services.
Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>
This config entry will be used to configure terminating gateways.
It accepts the name of the gateway and a list of services the gateway will represent.
For each service users will be able to specify: its name, namespace, and additional options for TLS origination.
Co-authored-by: Kyle Havlovitz <kylehav@gmail.com>
Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>
* Add Ingress gateway config entry and other relevant structs
* Add api package tests for ingress gateways
* Embed EnterpriseMeta into ingress service struct
* Add namespace fields to api module and test consul config write decoding
* Don't require a port for ingress gateways
* Add snakeJSON and camelJSON cases in command test
* Run Normalize on service's ent metadata
Sadly cannot think of a way to test this in OSS.
* Every protocol requires at least 1 service
* Validate ingress protocols
* Update agent/structs/config_entry_gateways.go
Co-authored-by: Chris Piraino <cpiraino@hashicorp.com>
Co-authored-by: Freddy <freddygv@users.noreply.github.com>
R.B. Boyer