* Cleanup the discovery chain compilation route handling
Nothing functionally should be different here. The real difference is that when creating new targets or handling route destinations we use the router config entries name and namespace instead of that of the top level request. Today they SHOULD always be the same but that may not always be the case. This hopefully also makes it easier to understand how the router entries are handled.
* Refactor a small bit of the service manager tests in oss
We used to use the stringHash function to compute part of the filename where things would get persisted to. This has been changed in the core code to calling the StringHash method on the ServiceID type. It just so happens that the new method will output the same value for anything in the default namespace (by design actually). However, logically this filename computation in the test should do the same thing as the core code itself so I updated it here.
Also of note is that newer enterprise-only tests for the service manager cannot use the old stringHash function at all because it will produce incorrect results for non-default namespaces.
Compiling this will set an optional SNI field on each DiscoveryTarget.
When set this value should be used for TLS connections to the instances
of the target. If not set the default should be used.
Setting ExternalSNI will disable mesh gateway use for that target. It also
disables several service-resolver features that do not make sense for an
external service.
Failover is pushed entirely down to the data plane by creating envoy
clusters and putting each successive destination in a different load
assignment priority band. For example this shows that normally requests
go to 1.2.3.4:8080 but when that fails they go to 6.7.8.9:8080:
- name: foo
load_assignment:
cluster_name: foo
policy:
overprovisioning_factor: 100000
endpoints:
- priority: 0
lb_endpoints:
- endpoint:
address:
socket_address:
address: 1.2.3.4
port_value: 8080
- priority: 1
lb_endpoints:
- endpoint:
address:
socket_address:
address: 6.7.8.9
port_value: 8080
Mesh gateways route requests based solely on the SNI header tacked onto
the TLS layer. Envoy currently only lets you configure the outbound SNI
header at the cluster layer.
If you try to failover through a mesh gateway you ideally would
configure the SNI value per endpoint, but that's not possible in envoy
today.
This PR introduces a simpler way around the problem for now:
1. We identify any target of failover that will use mesh gateway mode local or
remote and then further isolate any resolver node in the compiled discovery
chain that has a failover destination set to one of those targets.
2. For each of these resolvers we will perform a small measurement of
comparative healths of the endpoints that come back from the health API for the
set of primary target and serial failover targets. We walk the list of targets
in order and if any endpoint is healthy we return that target, otherwise we
move on to the next target.
3. The CDS and EDS endpoints both perform the measurements in (2) for the
affected resolver nodes.
4. For CDS this measurement selects which TLS SNI field to use for the cluster
(note the cluster is always going to be named for the primary target)
5. For EDS this measurement selects which set of endpoints will populate the
cluster. Priority tiered failover is ignored.
One of the big downsides to this approach to failover is that the failover
detection and correction is going to be controlled by consul rather than
deferring that entirely to the data plane as with the prior version. This also
means that we are bound to only failover using official health signals and
cannot make use of data plane signals like outlier detection to affect
failover.
In this specific scenario the lack of data plane signals is ok because the
effectiveness is already muted by the fact that the ultimate destination
endpoints will have their data plane signals scrambled when they pass through
the mesh gateway wrapper anyway so we're not losing much.
Another related fix is that we now use the endpoint health from the
underlying service, not the health of the gateway (regardless of
failover mode).
In addition to exposing compilation over the API cleaned up the structures that would be exchanged to be cleaner and easier to support and understand.
Also removed ability to configure the envoy OverprovisioningFactor.
This should make them better for sending over RPC or the API.
Instead of a chain implemented explicitly like a linked list (nodes
holding pointers to other nodes) instead switch to a flat map of named
nodes with nodes linking other other nodes by name. The shipped
structure is just a map and a string to indicate which key to start
from.
Other changes:
* inline the compiler option InferDefaults as true
* introduce compiled target config to avoid needing to send back
additional maps of Resolvers; future target-specific compiled state
can go here
* move compiled MeshGateway out of the Resolver and into the
TargetConfig where it makes more sense.
* connect: reconcile how upstream configuration works with discovery chains
The following upstream config fields for connect sidecars sanely
integrate into discovery chain resolution:
- Destination Namespace/Datacenter: Compilation occurs locally but using
different default values for namespaces and datacenters. The xDS
clusters that are created are named as they normally would be.
- Mesh Gateway Mode (single upstream): If set this value overrides any
value computed for any resolver for the entire discovery chain. The xDS
clusters that are created may be named differently (see below).
- Mesh Gateway Mode (whole sidecar): If set this value overrides any
value computed for any resolver for the entire discovery chain. If this
is specifically overridden for a single upstream this value is ignored
in that case. The xDS clusters that are created may be named differently
(see below).
- Protocol (in opaque config): If set this value overrides the value
computed when evaluating the entire discovery chain. If the normal chain
would be TCP or if this override is set to TCP then the result is that
we explicitly disable L7 Routing and Splitting. The xDS clusters that
are created may be named differently (see below).
- Connect Timeout (in opaque config): If set this value overrides the
value for any resolver in the entire discovery chain. The xDS clusters
that are created may be named differently (see below).
If any of the above overrides affect the actual result of compiling the
discovery chain (i.e. "tcp" becomes "grpc" instead of being a no-op
override to "tcp") then the relevant parameters are hashed and provided
to the xDS layer as a prefix for use in naming the Clusters. This is to
ensure that if one Upstream discovery chain has no overrides and
tangentially needs a cluster named "api.default.XXX", and another
Upstream does have overrides for "api.default.XXX" that they won't
cross-pollinate against the operator's wishes.
Fixes#6159
Also:
- add back an internal http endpoint to dump a compiled discovery chain for debugging purposes
Before the CompiledDiscoveryChain.IsDefault() method would test:
- is this chain just one resolver step?
- is that resolver step just the default?
But what I forgot to test:
- is that resolver step for the same service that the chain represents?
This last point is important because if you configured just one config
entry:
kind = "service-resolver"
name = "web"
redirect {
service = "other"
}
and requested the chain for "web" you'd get back a **default** resolver
for "other". In the xDS code the IsDefault() method is used to
determine if this chain is "empty". If it is then we use the
pre-discovery-chain logic that just uses data embedded in the Upstream
object (and still lets the escape hatches function).
In the example above that means certain parts of the xDS code were going
to try referencing a cluster named "web..." despite the other parts of
the xDS code maintaining clusters named "other...".
* Make cluster names SNI always
* Update some tests
* Ensure we check for prepared query types
* Use sni for route cluster names
* Proper mesh gateway mode defaulting when the discovery chain is used
* Ignore service splits from PatchSliceOfMaps
* Update some xds golden files for proper test output
* Allow for grpc/http listeners/cluster configs with the disco chain
* Update stats expectation
With this you should be able to fetch all of the relevant discovery
chain config entries from the state store in one query and then feed
them into the compiler outside of a transaction.
There are a lot of TODOs scattered through here, but they're mostly
around handling fun edge cases and can be deferred until more of the
plumbing works completely.
R.B. Boyer