Add support for setting QueryOptions on the following agent API endpoints:
- /agent/health/service/name/:name
- /agent/health/service/id/:id
- /agent/service/maintenance/:id
This follows the same pattern used in #9903 to support query options
for other agent API endpoints.
Resolves#9710
Previously, for a POST request to the /v1/operator/autopilot/configuration
endpoint, any fields not included in the payload were set to a zero-initialized
value rather than the documented default value.
Now, if an optional field is not included in the payload, it will be set to its
documented default value:
- CleanupDeadServers: true
- LastContactThreshold: "200ms"
- MaxTrailingLogs: 250
- MinQuorum: 0
- ServerStabilizationTime: "10s"
- RedundancyZoneTag: ""
- DisableUpgradeMigration: false
- UpgradeVersionTag: ""
CatalogDestinationsOnly is a passthrough that would enable dialing
addresses outside of Consul's catalog. However, when this flag is set to
true only _connect_ endpoints for services can be dialed.
This flag is being renamed to signal that non-Connect endpoints can't be
dialed by transparent proxies when the value is set to true.
* debug: remove the CLI check for debug_enabled
The API allows collecting profiles even debug_enabled=false as long as
ACLs are enabled. Remove this check from the CLI so that users do not
need to set debug_enabled=true for no reason.
Also:
- fix the API client to return errors on non-200 status codes for debug
endpoints
- improve the failure messages when pprof data can not be collected
Co-Authored-By: Dhia Ayachi <dhia@hashicorp.com>
* remove parallel test runs
parallel runs create a race condition that fail the debug tests
* Add changelog
Co-authored-by: Daniel Nephin <dnephin@hashicorp.com>
* Save exposed HTTP or GRPC ports to the agent's store
* Add those the health checks API so we can retrieve them from the API
* Change redirect-traffic command to also exclude those ports from inbound traffic redirection when expose.checks is set to true.
Also fixes a bug with listing kind=mesh config entries. ValidateConfigEntryKind was only being used by
the List endpoint, and was yet another place where we have to enumerate all the kinds.
This commit removes ValidateConfigEntryKind and uses MakeConfigEntry instead. This change removes
the need to maintain two separate functions at the cost of creating an instance of the config entry which will be thrown away immediately.
No config entry needs a Kind field. It is only used to determine the Go type to
target. As we introduce new config entries (like this one) we can remove the kind field
and have the GetKind method return the single supported value.
In this case (similar to proxy-defaults) the Name field is also unnecessary. We always
use the same value. So we can omit the name field entirely.
This config entry is being renamed primarily because in k8s the name
cluster could be confusing given that the config entry applies across
federated datacenters.
Additionally, this config entry will only apply to Consul as a service
mesh, so the more generic "cluster" name is not needed.
This way we avoid serializing these when empty. Otherwise users of the
latest version of the api submodule cannot interact with older versions
of Consul, because a new api client would send keys that the older Consul
doesn't recognize yet.
This PR replaces the original boolean used to configure transparent
proxy mode. It was replaced with a string mode that can be set to:
- "": Empty string is the default for when the setting should be
defaulted from other configuration like config entries.
- "direct": Direct mode is how applications originally opted into the
mesh. Proxy listeners need to be dialed directly.
- "transparent": Transparent mode enables configuring Envoy as a
transparent proxy. Traffic must be captured and redirected to the
inbound and outbound listeners.
This PR also adds a struct for transparent proxy specific configuration.
Initially this is not stored as a pointer. Will revisit that decision
before GA.
This PR adds support for setting QueryOptions on a few agent API
endpoints. Nomad needs to be able to set the Namespace field on
these endpoints to:
- query for services / checks in a namespace
- deregister services / checks in a namespace
- update TTL status on checks in a namespace
Some TLS servers require SNI, but the Golang HTTP client doesn't
include it in the ClientHello when connecting to an IP address. This
change adds a new TLSServerName field to health check definitions to
optionally set it. This fixes#9473.
This is done because after removing ID and NodeName from
ServiceConfigRequest we will no longer know whether a request coming in
is for a Consul client earlier than v1.10.
Daniel Nephin