Fixes#8466
Since Consul 1.8.0 there was a bug in how ingress gateway protocol
compatibility was enforced. At the point in time that an ingress-gateway
config entry was modified the discovery chain for each upstream was
checked to ensure the ingress gateway protocol matched. Unfortunately
future modifications of other config entries were not validated against
existing ingress-gateway definitions, such as:
1. create tcp ingress-gateway pointing to 'api' (ok)
2. create service-defaults for 'api' setting protocol=http (worked, but not ok)
3. create service-splitter or service-router for 'api' (worked, but caused an agent panic)
If you were to do these in a different order, it would fail without a
crash:
1. create service-defaults for 'api' setting protocol=http (ok)
2. create service-splitter or service-router for 'api' (ok)
3. create tcp ingress-gateway pointing to 'api' (fail with message about
protocol mismatch)
This PR introduces the missing validation. The two new behaviors are:
1. create tcp ingress-gateway pointing to 'api' (ok)
2. (NEW) create service-defaults for 'api' setting protocol=http ("ok" for back compat)
3. (NEW) create service-splitter or service-router for 'api' (fail with
message about protocol mismatch)
In consideration for any existing users that may be inadvertently be
falling into item (2) above, that is now officiall a valid configuration
to be in. For anyone falling into item (3) above while you cannot use
the API to manufacture that scenario anymore, anyone that has old (now
bad) data will still be able to have the agent use them just enough to
generate a new agent/proxycfg error message rather than a panic.
Unfortunately we just don't have enough information to properly fix the
config entries.
Related changes:
- hard-fail the xDS connection attempt if the envoy version is known to be too old to be supported
- remove the RouterMatchSafeRegex proxy feature since all supported envoy versions have it
- stop using --max-obj-name-len (due to: envoyproxy/envoy#11740)
A port can be sent in the Host header as defined in the HTTP RFC, so we
take any hosts that we want to match traffic to and also add another
host with the listener port added.
Also fix an issue with envoy integration tests not running the
case-ingress-gateway-tls test.
Previously, we did not require the 'service-name.*' host header value
when on a single http service was exposed. However, this allows a user
to get into a situation where, if they add another service to the
listener, suddenly the previous service's traffic might not be routed
correctly. Thus, we always require the Host header, even if there is
only 1 service.
Also, we add the make the default domain matching more restrictive by
matching "service-name.ingress.*" by default. This lines up better with
the namespace case and more accurately matches the Consul DNS value we
expect people to use in this case.
- Validate that this cannot be set on a 'tcp' listener nor on a wildcard
service.
- Add Hosts field to api and test in consul config write CLI
- xds: Configure envoy with user-provided hosts from ingress gateways
This commit adds the necessary changes to allow an ingress gateway to
route traffic from a single defined port to multiple different upstream
services in the Consul mesh.
To do this, we now require all HTTP requests coming into the ingress
gateway to specify a Host header that matches "<service-name>.*" in
order to correctly route traffic to the correct service.
- Differentiate multiple listener's route names by port
- Adds a case in xds for allowing default discovery chains to create a
route configuration when on an ingress gateway. This allows default
services to easily use host header routing
- ingress-gateways have a single route config for each listener
that utilizes domain matching to route to different services.
In addition to exposing compilation over the API cleaned up the structures that would be exchanged to be cleaner and easier to support and understand.
Also removed ability to configure the envoy OverprovisioningFactor.
This should make them better for sending over RPC or the API.
Instead of a chain implemented explicitly like a linked list (nodes
holding pointers to other nodes) instead switch to a flat map of named
nodes with nodes linking other other nodes by name. The shipped
structure is just a map and a string to indicate which key to start
from.
Other changes:
* inline the compiler option InferDefaults as true
* introduce compiled target config to avoid needing to send back
additional maps of Resolvers; future target-specific compiled state
can go here
* move compiled MeshGateway out of the Resolver and into the
TargetConfig where it makes more sense.
* connect: reconcile how upstream configuration works with discovery chains
The following upstream config fields for connect sidecars sanely
integrate into discovery chain resolution:
- Destination Namespace/Datacenter: Compilation occurs locally but using
different default values for namespaces and datacenters. The xDS
clusters that are created are named as they normally would be.
- Mesh Gateway Mode (single upstream): If set this value overrides any
value computed for any resolver for the entire discovery chain. The xDS
clusters that are created may be named differently (see below).
- Mesh Gateway Mode (whole sidecar): If set this value overrides any
value computed for any resolver for the entire discovery chain. If this
is specifically overridden for a single upstream this value is ignored
in that case. The xDS clusters that are created may be named differently
(see below).
- Protocol (in opaque config): If set this value overrides the value
computed when evaluating the entire discovery chain. If the normal chain
would be TCP or if this override is set to TCP then the result is that
we explicitly disable L7 Routing and Splitting. The xDS clusters that
are created may be named differently (see below).
- Connect Timeout (in opaque config): If set this value overrides the
value for any resolver in the entire discovery chain. The xDS clusters
that are created may be named differently (see below).
If any of the above overrides affect the actual result of compiling the
discovery chain (i.e. "tcp" becomes "grpc" instead of being a no-op
override to "tcp") then the relevant parameters are hashed and provided
to the xDS layer as a prefix for use in naming the Clusters. This is to
ensure that if one Upstream discovery chain has no overrides and
tangentially needs a cluster named "api.default.XXX", and another
Upstream does have overrides for "api.default.XXX" that they won't
cross-pollinate against the operator's wishes.
Fixes#6159
* Make cluster names SNI always
* Update some tests
* Ensure we check for prepared query types
* Use sni for route cluster names
* Proper mesh gateway mode defaulting when the discovery chain is used
* Ignore service splits from PatchSliceOfMaps
* Update some xds golden files for proper test output
* Allow for grpc/http listeners/cluster configs with the disco chain
* Update stats expectation
* Vendor updates for gRPC and xDS server
* xDS server implementation for serving Envoy as a Connect proxy
* Address initial review comments
* consistent envoy package aliases; typos fixed; override TLS and authz for custom listeners
* Moar Typos
* Moar typos
