There are some cross-config-entry relationships that are enforced during
"graph validation" at persistence time that are required to be
maintained. This means that config entries may form a digraph at times.
Config entry replication procedes in a particular sorted order by kind
and name.
Occasionally there are some fixups to these digraphs that end up
replicating in the wrong order and replicating the leaves
(ingress-gateway) before the roots (service-defaults) leading to
replication halting due to a graph validation error related to things
like mismatched service protocol requirements.
This PR changes replication to give each computed change (upsert/delete)
a fair shot at being applied before deciding to terminate that round of
replication in error. In the case where we've simply tried to do the
operations in the wrong order at least ONE of the outstanding requests
will complete in the right order, leading the subsequent round to have
fewer operations to do, with a smaller likelihood of graph validation
errors.
This does not address all scenarios, but for scenarios where the edits
are being applied in the wrong order this should avoid replication
halting.
Fixes#9319
The scenario that is NOT ADDRESSED by this PR is as follows:
1. create: service-defaults: name=new-web, protocol=http
2. create: service-defaults: name=old-web, protocol=http
3. create: service-resolver: name=old-web, redirect-to=new-web
4. delete: service-resolver: name=old-web
5. update: service-defaults: name=old-web, protocol=grpc
6. update: service-defaults: name=new-web, protocol=grpc
7. create: service-resolver: name=old-web, redirect-to=new-web
If you shutdown dc2 just before (4) and turn it back on after (7)
replication is impossible as there is no single edit you can make to
make forward progress.
Add a skip condition to all tests slower than 100ms.
This change was made using `gotestsum tool slowest` with data from the
last 3 CI runs of master.
See https://github.com/gotestyourself/gotestsum#finding-and-skipping-slow-tests
With this change:
```
$ time go test -count=1 -short ./agent
ok github.com/hashicorp/consul/agent 0.743s
real 0m4.791s
$ time go test -count=1 -short ./agent/consul
ok github.com/hashicorp/consul/agent/consul 4.229s
real 0m8.769s
```
Previously config entries sharing a kind & name but in different
namespaces could occasionally cause "stuck states" in replication
because the namespace fields were ignored during the differential
comparison phase.
Example:
Two config entries written to the primary:
kind=A,name=web,namespace=bar
kind=A,name=web,namespace=foo
Under the covers these both get saved to memdb, so they are sorted by
all 3 components (kind,name,namespace) during natural iteration. This
means that before the replication code does it's own incomplete sort,
the underlying data IS sorted by namespace ascending (bar comes before
foo).
After one pass of replication the primary and secondary datacenters have
the same set of config entries present. If
"kind=A,name=web,namespace=bar" were to be deleted, then things get
weird. Before replication the two sides look like:
primary: [
kind=A,name=web,namespace=foo
]
secondary: [
kind=A,name=web,namespace=bar
kind=A,name=web,namespace=foo
]
The differential comparison phase walks these two lists in sorted order
and first compares "kind=A,name=web,namespace=foo" vs
"kind=A,name=web,namespace=bar" and falsely determines they are the SAME
and are thus cause an update of "kind=A,name=web,namespace=foo". Then it
compares "<nothing>" with "kind=A,name=web,namespace=foo" and falsely
determines that the latter should be DELETED.
During reconciliation the deletes are processed before updates, and so
for a brief moment in the secondary "kind=A,name=web,namespace=foo" is
erroneously deleted and then immediately restored.
Unfortunately after this replication phase the final state is identical
to the initial state, so when it loops around again (rate limited) it
repeats the same set of operations indefinitely.
* Add integration test for central config; fix central config WIP
* Add integration test for central config; fix central config WIP
* Set proxy protocol correctly and begin adding upstream support
* Add upstreams to service config cache key and start new notify watcher if they change.
This doesn't update the tests to pass though.
* Fix some merging logic get things working manually with a hack (TODO fix properly)
* Simplification to not allow enabling sidecars centrally - it makes no sense without upstreams anyway
* Test compile again and obvious ones pass. Lots of failures locally not debugged yet but may be flakes. Pushing up to see what CI does
* Fix up service manageer and API test failures
* Remove the enable command since it no longer makes much sense without being able to turn on sidecar proxies centrally
* Remove version.go hack - will make integration test fail until release
* Remove unused code from commands and upstream merge
* Re-bump version to 1.5.0
* Add HTTP endpoints for config entry management
* Finish implementing decoding in the HTTP Config entry apply endpoint
* Add CAS operation to the config entry apply endpoint
Also use this for the bootstrapping and move the config entry decoding function into the structs package.
* First pass at the API client for the config entries
* Fixup some of the ConfigEntry APIs
Return a singular response object instead of a list for the ConfigEntry.Get RPC. This gets plumbed through the HTTP API as well.
Dont return QueryMeta in the JSON response for the config entry listing HTTP API. Instead just return a list of config entries.
* Minor API client fixes
* Attempt at some ConfigEntry api client tests
These don’t currently work due to weak typing in JSON
* Get some of the api client tests passing
* Implement reflectwalk magic to correct JSON encoding a ProxyConfigEntry
Also added a test for the HTTP endpoint that exposes the problem. However, since the test doesn’t actually do the JSON encode/decode its still failing.
* Move MapWalk magic into a binary marshaller instead of JSON.
* Add a MapWalk test
* Get rid of unused func
* Get rid of unused imports
* Fixup some tests now that the decoding from msgpack coerces things into json compat types
* Stub out most of the central config cli
Fully implement the config read command.
* Basic config delete command implementation
* Implement config write command
* Implement config list subcommand
Not entirely sure about the output here. Its basically the read output indented with a line specifying the kind/name of each type which is also duplicated in the indented output.
* Update command usage
* Update some help usage formatting
* Add the connect enable helper cli command
* Update list command output
* Rename the config entry API client methods.
* Use renamed apis
* Implement config write tests
Stub the others with the noTabs tests.
* Change list output format
Now just simply output 1 line per named config
* Add config read tests
* Add invalid args write test.
* Add config delete tests
* Add config list tests
* Add connect enable tests
* Update some CLI commands to use CAS ops
This also modifies the HTTP API for a write op to return a boolean indicating whether the value was written or not.
* Fix up the HTTP API CAS tests as I realized they weren’t testing what they should.
* Update config entry rpc tests to properly test CAS
* Fix up a few more tests
* Fix some tests that using ConfigEntries.Apply
* Update config_write_test.go
* Get rid of unused import
R.B. Boyer